Waterproof varnish Pools
ACRYLIC PAINT POOL IMPERMEABILIZANTE
Painting respects pool that visually support, to waterproof tile pools
It allows embalming or permanent water.
Prevents the penetration of moisture.
Very flexible, absorbs contractions and expansions.
Durable and transparent finish
Please read the operating instructions below for proper application.
NEED THIS PAINT THINNER (Read more on How to Use)
BUY PAINT FOR POOLS WATERPROOF GRESITE and other materials. BUY POOL PAINT SOLVENT thermoplastic acrylic colorless or transparent.
WATERPROOF VARNISH COMPOSITION FOR POOLS
Clear varnish formulated based on thermoplastic acrylic resins in solvent medium.
ADVANTAGES FOR POOLS WATERPROOF VARNISH SOLVENT (THERMOPLASTIC ACRYLIC PAINT FOR SWIMMING IN CLEAR or transparent)
Varnish Acrylic waterproofing solvent penetrates the substrate providing, thus very durable films resistant to ultraviolet rays and abrasion.
Their most remarkable water repellency properties are preventing it from entering the substrate and allow trapped moisture to escape to the outside.
WHERE TO USE THE WATERPROOF PAINT OR PAINT POOL POOL INCOLOR or transparent?
Recommended for the protection and decoration of all media construction, such as l adrillo, wood, stone, masonry, tile, mortar and for concrete curing and sealing printed.
Varnish pools, mainly indicated for waterproofing and repair of swimming pools with small losses, where we want to visually observe the bracket.
Repair and waterproof paint cups pools, where the cracks do not exceed 2 mm. (In case you overcome, we must first separate seal the cracks with a antigoteras paint, putty, etc ... depending on the support).
HOW TO USE THE WATERPROOF THERMOPLASTIC ACRYLIC PAINT POOL?
DIRECTIONS FOR USE
Please wait for 24 to 72 hours, after emptying the pool for perfect drying of the same, before painting.
And back to wait between five days and two weeks, after painting or varnishing it to refill the pool water for proper application. (The more time we can leave drying, the better)
-Remover Well the material surfaces to be painted must be dry, clean and consistent.
-The Surfaces to be painted must be free of dust, lime, grease and old and well dried paints.
-Clean While the tile of any traces of lime, so that when applying the above waterproof varnish, do not bleach and lime remains attached notice.
If the surface is not porous is recommended, with an abrasive wear it chemical or mechanical anchor for the perfect paint. (Especially in the case of ceramic tiles)
-Homogeneizar Removing the container contents thoroughly.
-The Application can be done by brush, roller
In the case of ceramic tiles, you must apply a first coat with roughly 30-35% dilution solvent, for proper anchoring. In all other media can be applied a dilution of 15%.
-The Second hand, it applies varnish extending well to avoid thick, dilute between 10% and 15% solvent layers.
-To Achieve good adhesion between coats must not let more than 24 hours elapse, pear must leave dry the layers, to avoid the appearance of bubbles or blisters.
-Let Conveniently dry before painting and before dam with water (minimum 48 hours)
PRECAUTIONS TO APPLY THE PAINT ACRYLIC WATERPROOF POOLS
Make a good ventilation in the room and have a good extraction system.
Use activated carbon mask, goggles and gloves during application.
Dilute conveniently varnish.
Do not apply thick layers, to support not bleach.
Leave the paint to dry between coats, to avoid blisters or bubbles appear.
We recommend not paint in the middle of the day. not to cause a very rapid to be very hot drying stand. (Best to apply early in the morning)
Thermoplastic acrylic varnish PRESENTATION IMPERMEABLE
It comes in bottles of 0.75 liters, 4 liters and 20 liters.
Technical advice for the use and application of our products are given with best knowledge and information, the result of tests conducted in our laboratories and our experience gained over the years customer service.
ANGAR paintings, SC will not be responsible for problems caused by incorrect application of the products.
IF YOU WANT TO KNOW THE PRICE OF PAINT thermoplastic acrylic GRESITE WATERPROOF POOLS, UP TO THE TOP OF THE PAGE
- Theoretical performance
- 4 to 6 LITER M2 X X HAND
- 12 HORAS
- Brightness / Satin
- Disolvente Industrial de Secado Rápido
- Useful of Application
- BRUSH / ROLLER
- Cleanliness Tool
- Industrial Dried Rapid Solvent
- Dissolution of the first hand
- Al 30% a modo de Imprimación
- Dissolution in the second hand
- al 10% - 15 % // Dilución Tercera mano al 10%
- 0.75 LITROS / 4 LITROS / 20 LITROS
- Humedad del soporte
- Inferior al 5 %